Laboratory Service

Block and Interlock Testing Laboratory in Jeddah

Testing for cement blocks, interlock pavers, and curbstones covering dimensions, compressive strength, water absorption, and density by product specification.

Block and Interlock Testing Laboratory

Block and Interlock Testing in Jeddah

Jeddah (Jiddah) projects receive many masonry and paving products, and they should not be treated as one category. Solid, hollow, load-bearing, and non-load-bearing blocks differ from interlock pavers and curbstones. Product identity, nominal size, batch, intended use, and specification must be clear before sampling.

Tests matched to the unit

Block testing may include overall dimensions, relevant wall or web thicknesses, compressive strength, absorption, density, or mass. Pavers and curbs may require geometric checks followed by compression, flexural, or splitting tests according to their classification. Results are compared with the stated ASTM, SASO, or project requirements; one test package does not suit every product.

Site sampling

Our Jeddah field team covers stacks in Al-Hamdaniyah, As-Safa, Ar-Rawabi, and As-Sanabil, and reaches Ar-Rawdah, Obhur, and Dhahban. On normal days, coverage windows range from 5–25 minutes to 90–120 minutes for Thuwal. Collection time depends on separated lots and safe handling.

Separate manufacturer, batch, type, and size; provide delivery records and the specification; confirm specimen quantity and sampling method; and protect units during removal and transport. Storage can be constrained in Al-Balad, Ash-Shati, or Al-Khumrah, so agree the collection point beforehand. The report describes tested units; full-lot acceptance follows the contract and quality plan.

Areas We Cover in Jeddah

Our Jeddah field team covers 153 districts across 14 municipal coverage groups. Listed times are typical on normal days and may vary with traffic and site readiness.

Taybah Municipality

≈ 5–25 min
15 districts · Show districts

Al-Furusiyah, Al-Bashair, Ar-Rahmaniyah, Al-Falah, Al-Hamdaniyah, As-Salihiyah, Al-Hijaz, At-Tawfiq, Al-Mawaddah, Al-Bayan, An-Nada, Al-Widad, As-Safwah, Al-Budur, Al-Wafa

Briman Municipality

≈ 15–35 min
13 districts · Show districts

Briman, Al-Ajawid, Al-Manar, As-Samir, Al-Muntazah, Ar-Rayyan, Al-Kawthar, East Umm Hablain, West Umm Hablain, Ar-Rawasi, At-Tilal, Al-Asla, King Fahd

Umm As-Salam Municipality

≈ 15–35 min
14 districts · Show districts

Umm As-Salam, Al-Mahamid, Al-Harazat, Ash-Shuruq, Al-Wahah, Quwayzah, Al-Muntazahat, An-Nakhil (Abraq Ar-Rughamah), Ar-Rughamah, Muraikh, Al-Qaws, Kinanah, Quba, East As-Sulaymaniyah

Airport Municipality

≈ 20–35 min
6 districts · Show districts

An-Nuzhah, Al-Marwah, Ar-Rabwah, As-Safa, Al-Bawadi, Al-Faysaliyah

Historic Jeddah (Al-Balad)

≈ 25–40 min
5 districts · Show districts

Al-Balad, Al-Mazlum, Ash-Sham, Al-Yaman, Al-Bahr

Al-Balad Municipality

≈ 25–40 min
7 districts · Show districts

Al-Kandarah, East Al-Baghdadiyah, West Al-Baghdadiyah, Al-Hindawiyah, As-Sabil, As-Sahifah, Al-Ammariyah

Ash-Sharafiyah Municipality

≈ 25–40 min
5 districts · Show districts

Ash-Sharafiyah, An-Naseem, Bani Malik, Al-Wurud, Ar-Ruwais

Al-Aziziyah Municipality

≈ 25–40 min
5 districts · Show districts

Al-Aziziyah, Al-Andalus, Al-Hamra, Mishrifah, Ar-Rihab

Al-Jami’ah Municipality

≈ 25–45 min
12 districts · Show districts

Al-Jami’ah, Ar-Rawabi, As-Sulaymaniyah, Al-Fayha, Ath-Thaghr, An-Nazlah Al-Yamaniyah, East An-Nazlah, Al-Qurayyat, Ath-Thaalibah, Petromin (Al-Karantina), Ghulail, Madain Al-Fahd

South Municipality

≈ 25–55 min
30 districts · Show districts

Al-Waziriyah, North Prince Fawaz, South Prince Fawaz, Prince Abdulmajeed, Al-Adl, Al-Fadl, Al-Mahjar, Al-Ajawid, Kilo 14, Al-Faruq, Al-Huda, As-Sanabil, Ash-Shifa, Al-Jawharah, At-Tadamun, As-Sururiyah, As-Sarawat, Al-Qawzain, At-Taawun, Al-Khumrah, Al-Karamah, Al-Fudaylah, Al-Qurainiyah, Ad-Dahiyah, Ar-Rahmah, Al-Barakah, Al-Masrah, Ar-Rabiyah, Al-Mustaqbal, As-Sahl

New Jeddah Municipality

≈ 30–50 min
5 districts · Show districts

Ar-Rawdah, As-Salamah, Az-Zahra, Al-Khalidiyah, Ash-Shati

Obhur Municipality

≈ 35–60 min
7 districts · Show districts

An-Naeem, An-Nahdah, Al-Muhammadiyah, Al-Basatin, Al-Murjan, Al-Asalah, South Obhur

Dhahban Municipality

≈ 50–90 min
20 districts · Show districts

North Obhur, Salman Bay, As-Sawari, Az-Zumurrud, Al-Yaqut, Al-Lulu, Al-Firdaws, Ash-Shira, Al-Amwaj, Ar-Riyadh, Taybah, Al-Fanar, Al-Buhayrat, Al-Manarat, An-Nur, Al-Muruj, Al-Khalij, An-Najmah, Az-Zuhur, Dhahban

Thuwal Municipality

≈ 90–120 min
9 districts · Show districts

Thuwal, Al-Kanadirah, Al-Bahharah, As-Sawalhah, Al-Amir, Abu Zayd, Az-Zanabiqah, As-Sarahin, Jawharat Thuwal

Estimated driving times from the lab on normal days; they can be longer during Ramadan and the Hajj season.

In Short

Block, interlock-paver, and curbstone testing measures properties of submitted product samples, such as dimensions, compressive strength, water absorption, and density where requested. The service starts by identifying the unit, intended use, governing specification, and sampling plan; results are then compared with the project-supplied limits rather than one value for every product.

Blocks, Interlock Pavers and Curbstones Laboratory Testing

Block products differ by material, configuration, and use: solid or hollow, load-bearing or non-load-bearing, insulating or lightweight, plus paving units and curbstones. A request saying only “block” is incomplete. Product type, size, intended use, batch, and specification are needed for the correct test and comparison.

Testing a delivered batch provides evidence about the tested samples. Result reliability begins with a sampling plan representing the batch, protected transport, and clear specimen identification. The laboratory records results against supplied requirements; acceptance of the entire delivery follows the quality plan, contract, and authorized project decision.

Record product type, batch, size, and intended use
Measure cement-block dimensions instead of relying on nominal size
Link strength, absorption, and density to the correct sample and standard
Flag deviations needing review before the full batch is installed

Cement Block and Interlock Paver Testing Scope

Unit type and intended use define the test; blocks, pavers, and curbstones are not treated as one product.

Concrete and Cement Blocks

Testing solid or hollow units under the project classification.

Actual dimensions and relevant wall or web thicknesses
Compressive strength with bearing area and calculation method recorded
Water absorption and density or mass where included
Comparison with the stated unit classification and intended use

Interlock Pavers and Curbstones

Tests for paving or edging units according to product form and specification.

Length, width, thickness, and required dimensional tolerances
Compressive, flexural, or splitting strength as specified
Water absorption and density where requested
Use-face, color, or shape identification where visual checks are scoped

Common References for Masonry and Paving Units

The required standard and edition are confirmed in the work order before comparison or conformity evaluation.

ASTM C140/C140M

Sampling, dimensions, compression, absorption, and density for specified concrete units

ASTM C90

Specification for load-bearing concrete masonry units where adopted

ASTM C129

Specification for non-load-bearing concrete masonry units where adopted

ASTM C936/C936M

Specification for solid concrete interlocking paving units

Project / SASO specification

Product limits, classification, and tolerances stated in the contract or named Saudi specification

From Batch Identification to Block and Paver Results

A usable result needs representative samples and a defined request, not unidentified units.

1

1. Define Product and Requirement

We collect product type, use, nominal size, manufacturer or batch data, standard, and acceptance limits.

2

2. Sample and Identify

Samples are selected under the project plan or received with source, quantity, condition, and visible damage recorded.

3

3. Measure and Test

Dimensions and specified strength or absorption tests are performed, recording specimen preparation and result calculations.

4

4. Report and Compare

The report lists each specimen result and the project-supplied requirement, flagging deviations for authorized review.

Included Tests

7 field and laboratory tests available by project scope

Compressive Strength

مقاومة إجهاد الكسر

ASTM C140

Unit: sample

Water Absorption

نسبة الامتصاص

ASTM C140

Unit: sample

Dimensions

الأبعاد

Unit: sample

Fire Resistance (blocks)

مقاومة الحريق (بلوك)

Unit: sample

Flexural Strength (where required by product standard)

مقاومة الانحناء (عند طلبها حسب مواصفة المنتج)

Unit: sample

Splitting Tensile Strength (where required)

مقاومة الشد الانشطاري (عند طلبها)

Unit: test

Density

الكثافة

ASTM C140

Unit: sample

Equipment used for this service

Why Choose Us

Why TECHNO Soil Lab?

7
Available Tests

Field and laboratory tests selected to match the project scope

15+
Years Experience

Accumulated technical experience in testing & engineering consultancy

5
Cities Served

Head office in Makkah, with equipped field teams in all five cities

The complete Block and Interlock Testing Laboratory guide

Test selection by project type, the pre-contract checklist, what drives the quote and what the report contains — on the main service page.

Read the full guide

Related Reading

Common Questions

FAQ About Block and Interlock Testing Laboratory

On normal days, listed coverage windows start at 5–25 minutes for the nearest group and extend to 90–120 minutes for Thuwal. Timing is an estimate by group and may change with traffic, entry clearance, and site readiness.

Other Services You May Need

Explore the rest of our accredited engineering tests in one place

Need Block and Interlock Testing Laboratory Services?

Our specialized team is ready to mobilize to your site anywhere in the Kingdom.