Concrete and Cement Blocks
Testing solid or hollow units under the project classification.
Testing for cement blocks, interlock pavers, and curbstones covering dimensions, compressive strength, water absorption, and density by product specification.

Concrete units used in Qassim (Al-Qassim) range from building blocks and walkway pavers to curbs and yards serving agricultural or commercial activity. A product label alone cannot select the test. Units may be solid or hollow, load-bearing or non-load-bearing, with distinct classifications, dimensions, and uses.
Blocks may require dimensions, relevant wall or web thicknesses, compressive strength, absorption, density, or mass. Pavers and curbs may need geometry checks followed by compression, flexural, or splitting work under the specified document. Product classification and the stated ASTM or SASO method govern project comparison; requirements should not be transferred between unit types.
Sampling can be arranged in Al Rass, Al Badayea, An Nabhaniyah, Al Fuwarah, and Dulay Rashid. On normal days, our Qassim field team covers Al Rass within 5–20 minutes, while far towns are listed at 70–120 minutes. Preparing stacks before travel avoids handling delays and selection from the wrong lot.
Separate each manufacturer, batch, product, and size into a marked stack. Provide delivery records, intended use, specification, and quantity. Permit safe selection under the plan and do not preselect units when random sampling is required. Photograph existing breakage and protect specimens during transport. Reporting describes tested units; full-lot acceptance follows the contract and quality plan.
Our Qassim field team covers 15 towns and municipalities across five groups around Al Rass. Listed times are typical on normal days and may vary with roads, entry clearance, and site readiness.
Al Rass
Al Badayea, Al Khabra, Riyadh Al Khabra, Qasr Bin Aqil
Al Bukayriyah, Ad Dulaymiyah, An Nabhaniyah, Dukhnah
Al Quwarah, Al Fuwarah, Az Zahiriyah, Dulay Rashid
Uqlat As Suqur, Dariyah
Estimated driving times from the lab on normal days; they can be longer during Ramadan and the Hajj season.
In Short
Block, interlock-paver, and curbstone testing measures properties of submitted product samples, such as dimensions, compressive strength, water absorption, and density where requested. The service starts by identifying the unit, intended use, governing specification, and sampling plan; results are then compared with the project-supplied limits rather than one value for every product.
Block products differ by material, configuration, and use: solid or hollow, load-bearing or non-load-bearing, insulating or lightweight, plus paving units and curbstones. A request saying only “block” is incomplete. Product type, size, intended use, batch, and specification are needed for the correct test and comparison.
Testing a delivered batch provides evidence about the tested samples. Result reliability begins with a sampling plan representing the batch, protected transport, and clear specimen identification. The laboratory records results against supplied requirements; acceptance of the entire delivery follows the quality plan, contract, and authorized project decision.
Unit type and intended use define the test; blocks, pavers, and curbstones are not treated as one product.
Testing solid or hollow units under the project classification.
Tests for paving or edging units according to product form and specification.
The required standard and edition are confirmed in the work order before comparison or conformity evaluation.
Sampling, dimensions, compression, absorption, and density for specified concrete units
Specification for load-bearing concrete masonry units where adopted
Specification for non-load-bearing concrete masonry units where adopted
Specification for solid concrete interlocking paving units
Product limits, classification, and tolerances stated in the contract or named Saudi specification
A usable result needs representative samples and a defined request, not unidentified units.
1. Define Product and Requirement
We collect product type, use, nominal size, manufacturer or batch data, standard, and acceptance limits.
2. Sample and Identify
Samples are selected under the project plan or received with source, quantity, condition, and visible damage recorded.
3. Measure and Test
Dimensions and specified strength or absorption tests are performed, recording specimen preparation and result calculations.
4. Report and Compare
The report lists each specimen result and the project-supplied requirement, flagging deviations for authorized review.
7 field and laboratory tests available by project scope
Compressive Strength
مقاومة إجهاد الكسر
Unit: sample
Water Absorption
نسبة الامتصاص
Unit: sample
Dimensions
الأبعاد
Unit: sample
Fire Resistance (blocks)
مقاومة الحريق (بلوك)
Unit: sample
Flexural Strength (where required by product standard)
مقاومة الانحناء (عند طلبها حسب مواصفة المنتج)
Unit: sample
Splitting Tensile Strength (where required)
مقاومة الشد الانشطاري (عند طلبها)
Unit: test
Density
الكثافة
Unit: sample
Field and laboratory tests selected to match the project scope
Accumulated technical experience in testing & engineering consultancy
Head office in Makkah, with equipped field teams in all five cities
Test selection by project type, the pre-contract checklist, what drives the quote and what the report contains — on the main service page.
Read the full guideOn normal days, typical arrival starts at 5–20 minutes within Al Rass, then 25–45 minutes for nearby towns, and reaches 90–160 minutes for the outer region. These estimates vary with roads, entry clearance, and site readiness.
Explore the rest of our accredited engineering tests in one place

Soil
A soil testing laboratory covering pre-construction boreholes, in-situ testing, sampling, laboratory analysis, and geotechnical reporting according to each project's scope.

Concrete
Fresh and hardened concrete testing covering slump, temperature, specimens, compressive strength, concrete cores, and non-destructive methods to project specifications.

Asphalt
Asphalt mixture and pavement testing covering Marshall, binder content, gradation, Gmm, cores, thickness, density, and compaction to project specifications.

Aggregate
Fine and coarse aggregate testing for gradation, relative density, absorption, bulk density, abrasion, and soundness by intended use and project specification.

Rebar
Rebar batch testing covering yield, tensile strength, elongation, bend, mass per metre, and chemical composition under the specified grade and project standard.

Chemical
Book a water or soil sample and get results within days — turbidity, total hardness, calcium, magnesium, pH, sulfates and chlorides, for drinking, irrigation, sewage, well, hotel and farm water.
Our specialized team is ready to mobilize to your site anywhere in the Kingdom.